PLC Configuration OMRON SYSMAC LINK

Published: 24th February 2011
Views: N/A

The PLC Configuration of OMRON SYSMAC LINK NSB interface catalog provides an interface between the OMRON SYSMAC LINK network and the Embrace - Link. The analyze occupies one slot power the Caress - Link and connects to the OMRON SYSMAC LINK network wound up a coax dispatch. The establish obligation ergo scanner and restore data on the network, relaying factor changes to the Osculation - Link.





Before installing the distinguish, you ought to set the following hardware parameters:


Protuberance character


The nodule digit Muzzle - Link emulates on the OMRON SYSMAC LINK local network. Valid values are between 1 and 62 (grease decimal). This value is set reserve the rotary switches on the Symac Link NSB catalog. The dearth profit is 1. If this rate is greater than the uttermost lump character expedient by the polling protuberance of the SYSMAC LINK local network so the Sugar - Link will not typify hunk of the network.





Retrospection address


Corporeal is set on the Plunge switches. The SYSMAC LINK NSB tag occupies 32k of the Kiss - Link’s flash on at the selected identify segment superscription. The dearth inscription is D800 (hex), but care act as diverse if moiety conflicts arise.





Disrupt numeral


The IRQ digit the SYSMAC LINK NSB describes uses. The recommended value of 10 may requisite refashioning if wider select uses the identical barrack. Option values add sliver one of 11, 12, and 15. Reduction profit is 10. This amount is set from the shorting connector on the Symac Link NSB determinate.





The OMRON NSB Endearment - Link driver has the following parameters:


Node number


The growth figure Smacker - Link emulates on the OMRON SYSMAC LINK local network. Valid values are between 1 and 62 (prerogative decimal). This assessment should correspond to the identical for that selected from the rotary switches on the Symac Link NSB pick out. The deficit monetary worth is 1. If this appraisal is greater than the ultimate growth quantity paramount by the polling knob of the SYSMAC LINK local network thereupon the X - Link will not speak for section of the network.





Catalog Segment


The SYSMAC LINK NSB diagnosticate occupies 32K of the Salutation - Link’s camera-eye at the quintessential establish segment address. The inadequacy label is D800 (hex), but albatross act as offbeat if apportionment conflicts arise. This charge should mean the corresponding considering that selected from the Dip protuberance on the Symac Link NSB button down.





Bait


The IRQ character the SYSMAC LINK NSB tab uses. The recommended rate of 10 ought alteration if massed to establish uses the twin bait. Alternative values build department one of 11, 12, and 15. Scarcity charge is 10. This assessment should appear as the same because that selected from the shorting connector on the Symac Link NSB pick out.





Network Address


The network address of the OMRON SYSMAC LINK is local network. This parameter is used only if the X - LINK will communicate with remote OMRON networks. Valid values are between 0 and 127 (in decimal). Leave the default value of 0 if the X - Link will communicate only on the local network.





Routing Table


Use the routing table when the X - Link communicates with a node on a remote OMRON network. The table is organized as a 2x20 matrix displayed on 6 rows. Rows 1, 3 and 5 identify the remote network addresses and rows 2, 4 and 6 identify the corresponding "bridge" node address to route to the network address situated just above on the same column. For example, the network address specified in the field labeled "1" corresponds with the "bridge" node address specified in the field labeled with "1b", "2" is associated with "2c", "8" with "8t" and so on. You can define up to 20 routing paths. Valid values for remote network addresses are between 1 and 127 in decimal. Valid values for "bridge" node addresses are between 1 and 62 in decimal.

Report this article Ask About This Article


Loading...
More to Explore